Connectors (Internal)

Connectors and their secrets.

Summary

Nearly all electrical and electronic equipment contains connectors. Some of these are very small or have latches or clamps to keep them connected. You can save frustration and possibly causing damage by being prepared for whatever you might meet.

Safety

Warning03.png
Equipment should be powered off before connectors are disengaged or re-engaged since all the connections in a multi-way connector may not be made or broken at precisely the same time. This could potentially cause damaging voltages or currents in the device.

Introduction

Connectors allow a device or appliance to be built out of various parts, modules or sub-assemblies which can be easily put together on an assembly line, but also allowing them to be taken apart for repair. A connector must provide a good electrical contact rated for the voltages and currents involved, must resist coming undone if subject to vibration or stress, and must fit within the physical size constraints of the device it serves. There are many different types of connectors which meet these demands in different ways.

Full size connectors

The connectors in household and kitchen appliances and power tools rarely cause problems except that they may be very stiff to undo. Occasionally they may have latches, which might not be immediately obvious, to prevent them accidentally coming adrift. (This is very common in vehicle electrics, which is likely to be subject to vibration.)

Crimp terminals

A crimping tool and a selection of crimp terminals.

There are several types of crimp terminals which are colour coded according to the diameter of wire they are intended for.

Spade terminals are very commonly found in domestic appliances, and simply consist of a flat piece of metal like a garden spade (though obviously much smaller). It may be attached to or part of a switch, an electric motor, or some other component, and a receptacle slides onto it to make a connection. After a number of years these can become very stiff to remove.

Fork and ring terminals are used for terminating a wire which is to be connected under a screw.

Male and female bullet terminals allow an in-line connection between two wires.

Latched connectors

Photos needed: latched connectors: flat latch, lever type

Quite commonly, a connector has a latch of some kind to prevent it shaking or being pulled loose. They are very common in automotive electrics where continual vibration could cause a connector to shake loose, but they are often seen in domestic items as well.

If a connector refuses to disengage, never pull hard on the wires, as they may break. Look for some kind of latch or catch. There are various types and you may have to examine it closely in order to determine how to pull, push, squeeze or lever it. Pulling on the connector at the same time may prevent the latch from disengaging. Sometimes a small flat screwdriver judiciously applied will help.

Some SATA disk data cables also have a latch, which you have to squeeze quite hard in order to release.

Ribbon connectors

Flexible ribbons with conducting tracks similar to printed circuit tracks are extensively used in portable electronic equipment such as cameras, laptops, smartphones and tablets. Several types of connector are used to connect these to a circuit board.

Snap-on connectors

A miniature snap-on ribbon connector.

A multi-way plug soldered to the ribbon mates with a socket mounted on the circuit board. To release, lift a corner of the plug with a fingernail or plastic opening tool and it should snap open very easily.

Reseating these can be a little more tricky as the plug and socket need to be correctly aligned, which is often difficult to see as the socket is generally hidden by the ribbon. A little patience may be required to find the correct alignment. Do not try to force it or you may damage it. When correctly aligned, with firm (but not forceful) finger pressure you will be able to feel it snap closed. Press both ends to make sure it's closed along its entire length.

Having closed one of these connectors it can pop open again if the ribbon is strained, for example if it's attached to a sub-assembly which has not yet been screwed back in place.

Battery connectors in smartphones and tablets are often of the snap-on variety, though of larger dimensions. You might think that makes them easier to work with, but this isn't always the case as considerably more force may be required to release them. Applied in the wrong way, this can sometimes cause the socket to detach from the board, which would be hard to repair.

Zero insertion force connectors

With these, there is no plug attached to the ribbon, but instead, the conducting tracks are exposed at the end and often gold plated. The end of the ribbon is inserted into the connector and then clamped in place with a small bar.

There are two types. In one, the bar has to be angled up with a fingernail or plastic opening tool to release the ribbon. In the other, the bar has a tab at each end which has to be pulled away from the body of the socket.

In both cases the release mechanism is delicate. It can normally be opened quite easily but too much force or force applied in the wrong way can break it. Repair would then involve microsoldering to replace the socket, though there is some chance you could clamp the ribbon by inserting a piece of card or plastic of the right thickness into the connector.

On reassembly it may take a little fiddling to get the ribbon to go into a narrow slot in the connector. Make sure the release bar is in the fully open position and that the ribbon is fully home before closing the clamping bar.

Photos needed: each type of ribbon connector

Miniature connectors

Photos needed: each type

  • mini/micro JST etc
  • Micro co-ax

Elastomeric connectors

Photo needed

Many devices contain a simple LCD display, usually monochrome, and displaying 7-segment numbers and maybe various status icons, or sometimes a low resolution graphic display. The most familiar examples are calculators, DECT and older mobile phones.

The LCD is glass and the connections on it are almost invisible conductive tracks deposited on the surface of the glass. An elastometric strip, also known as a ZEBRA connector, is a very simple and common method of making the connections between the display and a printed circuit board. The board has one or two rows of contacts exactly matching those on the LCD and the elastometric strip is sandwiched between them. This makes all the connections since it consists of alternating conductive and non-conductive rubber (or some rubber-like plastic) along its length. With several such layers per connection, no special alignment is needed.

The elastometric strip is under pressure between the LCD and the circuit board so as to make good contact, but with age it can loose its springiness, typically resulting in some segments of a 7-segment display no longer working, or one or more rows or columns of pixels in a graphic display failing. If you can arrange to increase the pressure on the strip this may help, or you could try gently squashing it in a direction at right angles to the normal pressure before refitting it.

External links